Shower Faucet Repair In Kleinburg, Barrie and GTA

Repairing a shower faucet in Kleinburg, Barrie, Vaughan and surrounding areas, can involve different steps depending on the type of faucet you have (single handle, double handle, tub/shower diverter, etc.). Here are general steps for a common repair scenario:
Safety FirstTurn Off Water: Locate and turn off the water supply to the shower. There are usually shutoff valves in the bathroom, often behind an access panel, or you might need to shut off the main water supply to your house.
Tools and Materials Needed:
- Screwdriver (flathead and Phillips)
- Adjustable wrench or specific size wrench
- Allen wrench (hex key) if applicable
- Plumber's tape or silicone grease
- Replacement parts (cartridge, O-rings, washers)
Steps to Repair:
- Remove the Handle:
- Pry off any decorative cap with a flathead screwdriver to reveal the screw holding the handle.
- Unscrew this screw and gently remove the handle. If it's stuck, you might need a handle puller or to gently tap and pry with a screwdriver.
- Check the Type of Faucet:
- Single Handle Cartridge: You'll see a retaining nut or clip holding the cartridge in place.
- Two Handle Faucet (Compression): You'll need to remove the stem after unscrewing the packing nut.
- Mixer/Volume Control: Look for the mechanism that adjusts temperature or water flow.
- Dismantle the Faucet:
- For Cartridge Faucets: Use an adjustable wrench or pliers to remove the retaining nut or clip. Pull out the old cartridge. Match it with a new one from a hardware store or online.
- For Compression Faucets: Remove the stem, replace the washer at the bottom, and possibly the O-ring or packing material around the stem.
- Inspect and Replace Parts:
- Inspect for wear or damage. Typically, O-rings, washers, and cartridges are the parts to replace.
- If you're replacing a cartridge, make sure to get the correct model for your faucet brand.
- Clean and Lubricate:
- Clean the area where the cartridge or stem sits. Use a toothbrush or cloth to remove any deposits.
- Apply plumber's grease or silicone lubricant to the O-rings or the new cartridge to ensure smooth operation.
- Reassemble the Faucet:
- Insert the new cartridge or reassemble the stem with new washers/O-rings.
- Secure with the retaining nut or clip for cartridges, or replace and tighten the packing nut for compression faucets.
- Reattach the Handle:
- Put the handle back on, secure it with the screw, and replace any decorative cap.
- Turn Water Back On:
- Slowly turn the water back on to check for leaks. If there's a leak around the handle, you might need to tighten it a bit more or check if you've missed an O-ring or washer.
Additional Tips:
- Water Flow: Check if the water flow has improved. If not, there might be debris in the aerator or a problem elsewhere in the plumbing.
- Temperature Adjustment: For mixer faucets, if the temperature control isn't working correctly after repair, you might need to recalibrate it, following the manufacturer's instructions.
- Leak Testing: Run the shower for a few minutes to ensure there are no slow leaks that only develop under pressure.
- Preventive Maintenance: To avoid future issues, clean your showerhead/aerator, use a water softener if you have hard water, and check for mineral build-up periodically.
If the repair seems too complex or if you're unsure about which parts to buy, it might be worthwhile to call Town House plumbing in Barrie. Always ensure you have the correct parts for your faucet model to avoid compatibility issues.
Back to services
Back to HOME
Up Front PricingBefore we begin any work, we will explain what is required to perform the job. We don't have any hidden fees, the total cost for the plumbing work will be given to you before we begin.
|
Same Day ServiceGet your plumbing issue solved today, by one of our experienced plumbers today!
|
Open 7 Days A WeekWe understand that a plumbing emergency can come on a weekend or late at night, we are open so you can get your plumbing issue solved.
|