Faucet Repair And Replacement In Kleinburg, Barrie and GTA

Do you have a leaking faucet? Does your faucet not work as it used to? Is it loose and wobbly? We at Townhouse Plumbing can repair your faucet in Barrie and surrounding areas.
Over time your faucets can break or wear out. This can cause the handle to not work as it should or have reduced water pressure to the faucet. Here are the most common issues with faucets in your home:
- leaking spout
- loose handle
- low flow coming out of the faucet
- leaking water supply
- leaking cartridge
- faucet doesn't have enough hot or cold water coming out
There are many issues you can have with your faucet. We have the experience and knowledge to diagnose the issue and fix it for you. We offer new installation and repair services. Our faucet repair services in Barrie, Kleinburg and surrounding areas provide you with the peace of mind that you're faucet wont cause any leaking damage to your home. We will repair or replace your faucet the right way the first time.
Repairing a faucet can often be a straightforward process if you follow these general steps:
- Identify the Faucet Type:
- Compression faucets have separate hot and cold handles and depend on a washer for water control.
- Ball faucets have a single lever that moves side to side for temperature and front to back for water flow.
- Cartridge faucets might have one or two handles and use a cartridge inside to control water flow.
- Ceramic disk faucets are known for their longevity and use ceramic discs to control water flow.
- Shut Off Water Supply:
- Turn off the water to the sink. Look under the sink for shutoff valves and turn them clockwise. If there aren't individual shutoffs, turn off the main water supply for your home.
- Remove the Handle:
- Use a flat-head screwdriver to pry off any decorative cap on the handle to access the screw. Remove the screw with an appropriate screwdriver or Allen wrench if it's a set screw. Pull the handle off.
- Dismantle the Faucet:
- For compression faucets, remove the packing nut, and then you'll see the stem which likely needs a new washer.
- For cartridge faucets, you'll need to remove a retaining nut or clip to access the cartridge itself.
- Ball faucets involve removing the cam, ball, and other small parts like seals and springs.
- Inspect Parts:
- Check for signs of wear or damage on O-rings, washers, seats, or cartridges. These are often the culprits behind leaks.
- Replace Worn Parts:
- Washers, O-rings, and cartridges can be purchased at hardware stores. For cartridge faucets, ensure you match the cartridge to the exact make and model of your faucet.
- Clean and Reassemble:
- Clean any areas where there was mineral buildup or debris. Lubricate new O-rings with plumber's grease or silicone lubricant before assembly. Reassemble the faucet in reverse order of how you took it apart, ensuring everything is tight but not over-tightened.
- Turn the Water Back On:
- After reassembly, slowly turn the water back on to avoid damaging newly installed parts with a sudden rush of water. Check for leaks.
- Test the Faucet:
- Run water through the faucet, checking for any drips or leaks at the handle or spout.
Additional Tips:
- Always use a strainer or cover the sink drain to avoid losing parts.
- If you're unsure about what parts to buy, many stores allow you to bring in the old parts for matching.
- For more complex repairs or if you're not comfortable with DIY, professional help might be necessary, but for many common leaks, this DIY approach can work well.
Back to HOME
Up Front PricingBefore we begin any work, we will explain what is required to perform the job. We don't have any hidden fees, the total cost for the plumbing work will be given to you before we begin.
|
Same Day ServiceGet your plumbing issue solved today, by one of our experienced plumbers today!
|
Open 7 Days A WeekWe understand that a plumbing emergency can come on a weekend or late at night, we are open so you can get your plumbing issue solved.
|